Jun 14, 2019 How To Hack Apple Mac EFI Bios Firmware Password On A MacBook Pro 2011. If you're reading this, I'm guessing you yourself is on a mission to remove an unknown bias password from a Macbook pro. I'll start off with the tools you will need in order to spare you the read Tools needed. Remember, this is bypassing the boot-level firmware password. Most Macs have the software based password protection enabled only in the form of a user login and password. If this is the case, you can use methods to reset a forgotten Mac password to get around the user login completely (instructions for OS X Lion are slightly different). Boot up your Mac, and you should not see the firmware lock again. Disable the Password With Firmware Password Utility. Restart your Mac while holding down the Command + R keys to enter Recovery Mode. When the Utilities screen appears, go the Utilities menu bar, and select “Firmware Password Utility”. Choose to turn the Firmware Password off.
The Mission
There has been much controversy on removing the firmware lock on a MBP, MBA, or similar Mac’s. The MBA is a bit more complicated without a specialty tool to interface with a header on the board. We use to have to remove the board, scratch back traces, and solder directly to them which can be seen in EX-1.1. This is just short of replacing the entire chip, which is what we are all trying to avoid right? I also have a project I have been forking on called the iFLRT (Firmware Lock Removal Tool) that can be found HERE. Donate what you can to keep my development process alive, every little red cent helps.
Hack Mac Firmware Password Download
First you need to understand what the firmware lock is and how removing it will affect you. Then maybe you will be able to decide if this procedure is for you. In most cases a MBP has been purchased from a third party who may have stolen it or simply forgotten to remove their iCloud account. In this case the symptoms would be a four digit pin lock when the OS loads. When you try to do a re-install you are met with a lock screen shown in EX-1. This is the result of the Mac being most definitely locked from the cloud. There are two options from this point which are explained below.
EX-1EX-1.1
NOTE: If you have a 2010 model MBP or earlier all you have to do is change the amount of RAM in your MBP and clear the PRAM. This is all you have to do to get past OS lock. But you will still have a firmware lock as far as I know as in many cases this has happened. There have been occasions where the firmware lock has also been removed but I cannot contest to any exact models. Remember to set the Mac up like new and register the Mac with a new iCloud account to avoid any future lock-downs.
Option A: You can assume that a firmware lock was never set and brute force the firmware lock with a HID device such as a Teensy. This operation can take quite a while because it has to go through 10,000 iterations of possible pass-phrases in the worst case scenario. This will ONLY work if it was set by the iCloud!
Option B: You can assume that a firmware lock was indeed implicated when the MBP was set up and that the brute force method will not work. This can save you time but requires you to have a SPI programmer at hand such as the Bus Pirate or in this case a Raspberry Pi.
In A Nutshell
I won’t waste time on the brute force method as I believe it isn't relevant in most cases. I will focus on the process of flashing the EFI chip that is usually easily accessible by removing the Macs’s back-plate, either by a small 15X2 header, 17X2 header, or the 8 pin SOIC chip itself. You can see an image of the SOIC8 chip in EX-2 and the header in EX-2.1. The process is simple but requires a bit of knowledge in micro controllers. I will use the easiest and cheapest route that I know. The process goes briefly like this:
EX-2EX-2.1
Step 1 – Buy a SPI programmer such as the Raspberry Pi and a clip to interface with the chip. You can find the Pi on eBay, doesn't matter what model and you can find the Pomona SOIC8 clip there as well, usually with the female-to-female wires included. If you have a MBA then you can contact me about purchasing a clip for the header.
Step 2 - Read the chip three times and verify MD5 check-sum to ensure you have a good backup if things go wrong.
Step 3 – Make a copy of the dump and open it in a hex editor. I use Notepad ++.
Step 4 - Search for “$SVS” in the dump and you should find 2 instances. The first instance is what you will need to clear out making sure to keep the file length the same. It is safe to replace it with an empty value such as “ÿ”. The string including the $SVS should be replaced, you can copy and paste a portion of the string below if needed. each 'ÿ' is 2 bits and 8 bits make a byte So keep that in mind when you replace the string. The file size has to be exactly the same size as the chip or it will return an error.
This is an example of what to replace in a hex editor.
Step 4.1 – Get a clean dump that is not firmware locked from the community making sure you use the correct EMC and processor architecture. Make absolutely sure it is the same size as your original dump which is usually 2, 4, or 8 MB. If you go this route then you will need to replace the serial of the donated dump with your own serial in order to not register over their Mac. You can do this my simply searching for 'override-version' and on that same line there will be an 11 to 12 digit serial number that you will replace with your own. I also have a repository found HERE which you can use to search for your EMC number and I may have a clean dump.
Step 5 – Hook your programmer up to the chip, erase the chip, write the new dump and verify it.
Step 6 – Remove the clip and turn your Mac over to turn it on and test. You will immediately use the hot-keys to get to single user mode to test.
Step 7 – If you do not get to SU mode or the Mac does not boot right you will need to erase the chip and write the old dump back to it. You then can exhaust other options.
Step 7.1 – If you do get to SU mode turn the Mac back off and use the hot-keys to clear the PRAM. This will get rid of the 4 digit lock at OS load. Or you can simply re-install at this point. Remember to register the Mac to a new iCloud account to avoid future lock downs.
NOTE: Here are a few things worth mentioning..
It can help users who need to store a large number of data save much cost.Besides, every kind of RAID disk array can seek balance among read-write performance, data protection level, data rebuilding speed, and real disk space. Is there a free partition manager that can help users to resize RAID partition? Mac software raid two 2tb partitions windows 10. It is an excellent computer technology.Well then, how to? In users' eyes, Hard Disk RAID is a pretty ripe technology, and it is also regarded as the basic technology of data storage.
That is the entire process in a nutshell. Now I will explain how you can do this in as much detail as possible. The first thing that you will need to do is pick up your entire inventory before you begin. After that lay everything out and do some testing. Make sure your chip is supported having the datasheet and any diagrams available. I also suggest after you get the clip connected to all the wires you check for continuity from the clips pins to the end of the F-F wires on each pin.
Down And Dirty
NOTE:Read this guide in its entirety before you attempt to do anything to your Mac; Read it twice if you have to. I would also like to take this time to tell you that I am not responsible for any damages to your personal property or your physical/mental wellness if the guide is used. There is no guarantee, implied or expressed, in this procedure. You are following this guide knowingly and accept that damaging your property may be the outcome. Although I do not for see that being the case as I have tested this method many times. With that being said, let’s get started.
This is the list of things you will need in order to successfully and easily fix your MBP:
Now, I am going to assume that you at least have some experience in Linux and basic troubleshooting skills. You will run into problems and they are not all going to be the same as everyone else’s problems. So critical thinking is also required although I have not added it to the list. When you have your Raspberry Pi all set up and Raspian is booted up you will need to set it up for the first time. if you have already set it up go to the terminal and type:
sudo raspi-config
While in this configuration screen make sure to turn SPI on under Advanced. You may also turn on SSH if needed.
Then you will need to do an update by typing:
sudo apt-get update
Followed by an upgrade:
Bypass Mac Firmware Password
sudo apt-get upgrade
Optionally doing a distrobution upgrade:
sudo apt-get dist-upgrade
Now we have to install a few libraries that Flashrom relies on:
sudo apt-get install pciutils
sudo apt-get install libftdi-dev
sudo apt-get install libusb-dev
sudo apt-get install libpci-dev
Then you need to download the latest flashrom version:
sudo git clone https://github.com/stefanct/flashrom.git
It will be downloaded into a folder called 'flashrom' so change directory into the folder:
cd flashrom
And make it:
sudo make
Then install it:
sudo make install
Now we need to modify the blacklist by commenting out the SPI entry if it exists:
Sudo nano /etc/modprobe.d/raspi-blacklist.conf
11 easy tips to secure your Mac against hackers Create a standard user account. A standard user account is a non-admin account of Mac. It is recommended to use a. Disable Automatic user login. By default, Mac is set up to automatically login to your user account. This is a potential. Best way to protect mac from hack.
You will need to put “#” in front of the line that reads blacklist spi-bcm2708 effectively commenting it from the configuration file. If there is nothing in the file don't worry about it, that means SPI is not blacklisted. You can then save by hitting CTL+X, Y, and ENTER. You will then need to hook the wires up to the Pi and to the clip according to the diagrams below and your chip's datasheet. In MOST cases it will be just like what you see below.
The actual pinout for most 25 series chips depicted above is as follows for those of you who need a more definitive answer:Bypass Mac Firmware Password Macbook Air
Connect the wires on the clip to the Raspberry Pi making sure it is turned off following the diagram above. The GPIO pin that is closest to the corner of the Raspberry Pi is pin 2, keep that in mind or read the manual. After you are all connected you will place the clip on the chip snugly and turn the Pi on. Go to your working directory and run the following commands using some discretion.
**Start of the Flashrom process**Hack Mac Firmware Password
Get to the help page:
sudo flashrom --help
List the supported chips:
sudo flashrom –L
Read the flash chip by using the below command three times:
sudo flashrom –r ~/efi/read1.bin -V -p linux_spi:dev=/dev/spidev0.0
Erase the chip after you have verified all three reads have a matching MD5 hash:
sudo flashrom -E -V -p linux_spi:dev=/dev/spidev0.0
Using the methods explained above either modify or get a clean dump making sure it is the same size as the original ROM and write it to the chip:
sudo flashrom -w ~/efi/new.bin -V -p linux_spi:dev=/dev/spidev0.0
Verify the chips contents with the file that you just wrote to ensure its integrity:
sudo flashrom -v ~/efi/bnew.bin -V -p linux_spi:dev=/dev/spidev0.0
If you have not run into any problems you will have a freshly flashed chip. If you did run into issue, use the forum here to start a thread and we will help you troubleshoot your error messages. The reason I always use the –V command is to ensure a verbose output. At this point shut your Pi down and then remove the clip. You will then replace your power supply to the Mac and then turn it on using hot-keys to try and get to SU mode. If you get to SU mode you will shut back down and use the hot-keys to clear PRAM and reinstall setting the Mac up as a new machine. Make sure to register it with a newly created or existing iCloud account to prevent further incidents. If you did not get to SU mode you will need to erase your chip and try again.
That’s it folks, this is the long awaited guide that has more than enough information to get you through the process. It is specifically designed to save you money in the recovery of your Mac and to seamlessly work through any prior issues you may have had using Flashrom with a windows PC. If this guide has helped you please think about the years of work I have spent making this possible for you and donate to my iFLRT project to make it even easier for others. Or you can donate to me by using the slider on the edge of the left hand side of the page to donate to my personal PayPal account. Good luck to you all and Happy Hunting…
View the discussion thread.
Text Size
Locking your Mac with a password can go a long way to protecting your data. But, of course, there are ways around a simple account password.
You can also encrypt your Mac’s drive using Apple’s built-in FileVault platform. But FileVault won’t prevent an attacker from booting up your machine from an external hard drive.
If you are truly concerned about the privacy and security of your Mac, one of the strongest measures available is a firmware password.
How I turned my phone into a hacking machine Leave a Reply There are probably hundreds (if not thousands) of tutorials on this, but since I wanted a portable, non rooted, disposable hacking device which has the ability to take calls (a.k.a a cellphone/smartphone), I decided to. Turn your android phone into a hacking machine from these amazing tech tricks. If you really want to convert your android phone into a hacking device try these hacks in your android phone. If you really want to convert your android phone into a hacking device try these hacks in your android phone. Turning a mac into a hacking machine. Top 10 Tricks To Turn Your Android Into A Hacking Machine Auditing the security of your networks and devices is not only reserved for computers, your Android can also become a powerful hacking machine from which you can analyze the security of wireless networks and prevent anyone from connecting to your Wi-Fi network or use your Android as an.
Here’s what you need to know.
Benefits and Drawbacks
Unlike regular passwords, which can be deleted or reset, a firmware password exists in persistent memory on your Mac. In other words, it’s nearly impossible for most people to bypass.
As mentioned earlier, a firmware password will prevent anyone from accessing any disk on your Mac except the designated startup disk (without the password).
On the other hand, there are a couple things to keep in mind if you’d like to use a firmware password.
Notably, it isn’t easily reset. If you ever forget your firmware password, you’ll need to schedule an in-person appointment at a Genius Bar or Authorized Service Provider and bring a proof-of-purchase.
A firmware password will also prevent some Mac startup key combinations from working.
Enable Firmware Password
Once you weigh out the pros and cons, you can enable or disable your Mac’s firmware password using Recovery Mode. Here’s how.
If you’d like to disable your Mac’s firmware password, just use the same steps as above. The only difference is that in step 6, you’ll see Turn Off Firmware Password… instead.
You’ll need to actually input your firmware password to deactivate it, so make sure to write it down and keep it in a safe place.
One-time Firmware Password
If the unthinkable happens and your Mac is lost or stolen, you can also set a one-time firmware password remotely using Find My Mac.
Just open up the Find My iPhone app on an Apple device or in a browser via iCloud.com. Then select your Mac and use Lock MyMac.
According to Apple, the passcode you set using the Lock your Mac feature is actually a firmware passcode. That means it will prevent anyone from starting up your Mac from an external hard drive while it’s lost.
To unlock a Mac that you locked down using Find My iPhone, just enter the passcode when you get it back.
Read Next:How to Transfer Photos from Your iPhone to Your Mac or PC
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |